carbon steel elbow machine manufacturerelbow machine -Cangzhou Aocheng Machinery Equipment co., LTD

Description

elbow machine carbon steel elbow machine
elbow machine itself belongs to non-standard products, so there is no specific specifications and models, we can directly customize elbow machine according to customer requirements.We can make elbow diameter from 21mm-630mm and wall thickness from 3mm-30mm.The main characteristic of elbower is its low cost.
The elbower includes a frame, a working table, a side working table, an oil press, a fuel tank, an electrical box and a control board, as well as a forming mold, a mold lifting device and a stripper.The frame is a whole frame structure.The hydraulic press includes a vertical hydraulic press arranged vertically between the columns and a horizontal hydraulic press arranged horizontally between the middle part of the columns.The motor of the hydraulic press is arranged on the upper part of the machine.A large flow low pressure pump set is added on the upper part of the machine to connect the vertical compression cylinder to make the cylinder move quickly.The electrical box and control board control the operation of the machine by computer and microcomputer.
When the upper slide plate and all the positioning axes are not at the origin, the operation returns to the origin program.After the equipment is started, operate in the air for 1-2 minutes, and move the skateboard for 2-3 times with full stroke. If there is any abnormal sound or problem, park the car immediately, clean up the problem, and then operate after everything is normal.
The elbow machine should be under the unified command of one person during operation, so that the operator and the feeding restriction personnel cooperate closely, to ensure that the cooperative personnel are in the safe position to announce the bending signal.It is necessary to compacting the sheet when bending, in case the sheet becomes warped and hurts people.It is necessary to cut off the power supply when the die is adjusted.When changing the opening of the variable die, do not allow any material to contact with the die.
When the machine tool is working, the rear part of the machine tool is not allowed to stand.Stop pressing the sheet at one end alone.If the workpiece or mold is found to be out of alignment during operation, parking and proofreading should be performed to prevent hand damage.To prevent excessive thickness of iron plate or quenched steel plate, high-grade alloy steel, square steel and sheet material beyond the performance of sheet bending machine, so as not to damage the machine.Often check the upper and lower mold fit;Is the gauge indication in accordance with the regulations?Abnormal immediately stop, see the reason and timely cleaning.
Before elbowing the machine, place wooden blocks on the lower dies under the oil cylinders on both sides and drop the upper slide onto the wooden blocks.First exit the control system program, then shut off the power supply.
The new elbow produced by our company has low noise, more compact and reasonable arrangement of each part.
elbow machine needs 60 days to customize, need elbow machine to be customized in advance.Welcome customers to visit our company to negotiate.

Description

Specification

Consulting

Technical parameters（305306）

Model	BHEH-6	BHEH-12	BHEH-24	BHEH-30	BHEH-36	BHEH-48	BHEH-56
Processing range	1"~6"	3"~12"	8"~24"	16"~30"	20"~36"	30"~48"	32"~56"
Max. wall thickness	Sch40
Max. pressure	31.5MPa
Working pressure	25MPa
Working speed	0~1000mm/min
Return speed	1500~2000mm/min
Cylinder diameter	125mm×2	180mm×2	300mm×2	320mm×2	360mm×2	280mm×4	320mm×4
Cylinder stroke	3000mm	4000mm	5000mm	5000mm	6000mm	8000mm	10000mm
Cylinder thrust	30T×2	30T×2	175T×2	200T×2	250T×2	150T×4	200T×4
Motor power	18.5kW	22.5kW	37.5kW	48kW	56kW	68kW	80kW
IF power supply needed	160kW	250kW	400kW	500kW	600kW	800kW	1000kW