简体中文 | English
SEARCH:
Home About us Products Press Room Service Certificate Case Show Technical Support Contact Us
You are located : Home > Products > Mid-Frequency Induction Pipe Expanding Machine >
 
Direct sale medium frequency pipe bender
Introduction to the use of the intermediate frequency power supply: see the use of the intermediate frequency transformer voltage adjustment, when the transformer is running, including no load, it is forbidden to stop the supply of cooling water, the water should be smooth, prevent water splashing into the transformer
 
If you can envision it,We can supply it. E-mail:15230713671@163.com
Description Specification Consulting  
Direct sale medium frequency pipe bender

Introduction to the use of the intermediate frequency power supply: see the use of the intermediate frequency transformer voltage adjustment, when the transformer is running, including no load, it is forbidden to stop the supply of cooling water, the water should be smooth, prevent water splashing into the transformer.Before bending the pipe should be carefully adjusted, so that the center of the chuck and the induction ring are consistent, and the supporting drum to support the workpiece is adjusted at an appropriate height, so that the workpiece is smoothly fed into and the curved pipe and the straight section are in the same plane.Before operating frequency pipe bender, shall, in accordance with requirements of the medium frequency power supply and medium frequency transformer instruction in ready to intermediate frequency pipe bender and open pipe equipment, open said cooling pump and workpiece cooling water pipe equipment, when the temperature of the heat pipe to bend is greater than 910 ℃, for different pipe wall thickness must be heated to a temperature above 950 ℃,And the temperature of the inner wall should be kept above 910℃ at least, but not higher than the allowable heating temperature of the process for the pipe, before starting the main motor for bending operation, heating to the bending temperature or the workpiece is not heated, it is forbidden to start the main motor.After bending, stop heating, before loosening the clamp head, it is forbidden to open the main motor for the reverse operation of the rotary arm.Because the diameter and wall thickness of the pipe are different, the heating power and bending velocity of the pipe are also different, so the parameters of the pipe should be found out step by step in practice.

For the intermediate frequency pipe bender parameters and bending multiple are made according to the customer to manufacture different types and bending radius of the intermediate frequency pipe bender, the intermediate frequency pipe bender in bending due to the effective force on the V-wheel, so in bending diameter wall thickness pipe, by adjusting the screw so that the two V-wheel can withstand the thrust evenly,Avoid the damage of the intermediate frequency pipe bender caused by the thrust concentrated on a V wheel due to improper adjustment.For bending the pipe with accessories, the V-wheel of the accessories shall be mounted on the same slide seat as the supporting V-wheel.For the middle frequency pipe bender in the last bend and the pipe with short supporting finger end, the V-type wheel on the attachment can be removed and installed on the supporting seat of the middle frequency transformer to shorten the distance between the support and the center of the bend. For several kinds of pipes with special force, the thrust can also be dispersed on the three V-type wheels by bending pipe.

The company mainly produces a variety of different types of medium frequency pipe bender, medium frequency elbow machine, tee machine, medium frequency pipe expanding machine, elbow beveling machine, rolling machine and other pipe fittings equipment, the way to buy the company's above pipe fittings equipment customers our company will let each customer enjoy a low price to buy satisfactory equipment.

415

 
New Products
- Direct sale med...
- Pipe fitting eq...
- Direct sale med...
- Pipe bender ben...
- Manufacturing pipe bender
- Manufacture medi...
- Medium frequency...
Top Products
- Automatic Triple...
- Automatic Double...
- Hydraulic Press
- Elbow Cold Forming Machine
- Elbow Hot Forming Machine
- Single-Head Pipe...
- Pipe Bending Machine
Hot Products
- Automatic Triple...
- Automatic Double...
- Hydraulic Press
- Elbow Cold Forming Machine
- Elbow Hot Forming Machine
- Single-Head Pipe...
- Pipe Bending Machine
Quick to find the product information
 
Contact us
Cangzhou Aocheng Machinery Equipment co., LTD.
Address : Bobei Industrial Zone, Mengcun Hui Autonomous County, Cangzhou City, Hebei Province, China
Mobile : +86-15230713671
Fax : +86-317-6218625
E-mail : 15230713671@163.com
Skype : zhiguang.wu
About Us |  Products |  Order Online |  Contact Us Copyright © Elbow Machine,Elbow Forming Machine,Tee Machine All Rights Reserved manage